SRPNT by Throne Cycles Assembly Guide

Model: SRPNT by Throne Cycles 72V E-Moto

Open the box and remove components:
- Save zip ties and packing materials for reuse.
- Remove: handlebars, front wheel, charger box, seat, display, fenders, and peg hardware.
Locate your keys:
- Keys are in a small box inside the main packaging.
Remove battery:
- Pull seat release latch and remove seat.
- Push the rear latch button and pull battery toward the rear of the bike.
- Unplug battery connector and set battery aside for charging.
Charge the battery:
- Use the included 84V 9A charger.
- Plug battery in and verify charge level (typically ships 70–80% charged).
- Avoid placing the charger near your filming area—fan hum is audible.

Remove axle:
- Loosen pinch bolts on the fork using 8mm Allen.
- Use a dead blow and small screwdriver to tap the axle out.
- Do not hammer the axle directly—threads can be damaged.
Prepare axle and spacers:
- Lightly grease axle and rubber edges of spacers.
- Position one spacer into left fork leg.
- Insert wheel with brake rotor aligned into left fork leg.
- Slide axle through, add second spacer on right, and push axle fully in.
Tighten components:
- Finger-tighten axle bolt with 8mm Allen.
- Alternate tightening pinch bolts evenly, then snug the axle bolt.
- Torque all bolts to spec.

Check both front and rear rotors:
- Confirm they are 3mm thick with Torx or hex rotor bolts.
- Remove each rotor bolt one at a time, apply blue Loctite, reinstall and torque to spec.
- Do this for both front and rear to prevent future vibration or loosening.

Install throttle and brake lever:
- Slide throttle onto handlebar before installing bars in stem.
- Lightly snug bolts with 4mm Allen. Finalize throttle angle and snap-back function.
Mount handlebars:
- Insert into direct-mount stem and hand-tighten the four clamp bolts.
- Adjust bar position to your preference (stem has 3 adjustable positions).
Install reflectors:
- Thread into sides of fork legs or handlebar area.

Locate and connect brake motor cutoff switches:
- Remove plastic spacers from brake connectors.
- Match HEGO-style male/female connectors and align pins properly.
- Click securely into place—do not force.
Optional:
- Disconnect motor cutoffs if you prefer throttle control during aggressive riding or wheelies.
- (SRPNT does not yet have app-based toggling for this feature.)

Fender and chain guard:
- Use supplied bolts (4mm Allen) with Loctite.
- Do not overtighten; secure just enough to hold in place.
- Chain guide is metal with a plastic liner—ensure snug fit.
Display:
- Use included 4mm bolts and aluminum mount.
- Plug in using keyed connector—listen for two clicks.
- Leave slightly loose if you want to adjust visibility while riding.

Footpeg Installation:
- Use included locking nuts—no Loctite required.
- Consider your preferred peg position (middle by default).
- REV Rides offers upgraded pegs and colors.
Frame Brace Positioning:
- Three positions: front, middle, rear.
- Rear is recommended for extra support if pegs are set forward.

Insert battery:
- Slide in from the rear until fully seated.
- Connect battery leads using keyed plug—press until latched.
- Lock the battery connector using the side button.
- Replace underseat port cover and seat.

Secure cables:
- Zip tie throttle and brake lines to prevent movement.
- Tuck wiring behind metal cable guides where applicable.
- Clip zip tie tails and rotate them out of sight for a clean finish.

Remove protective plastics and stickers
Check tire pressure
Check chain slack and lube the chain
- Clean and re-lube every dirt ride or weekly for street use.
- Expect chain stretch during the first 100–300 miles.
Check spoke tension after 50 miles
- Refer to manual or upcoming REV Rides tutorial for truing wheels.
Adjust suspension
- Front fork is adjustable KKE air fork (use proper shock pump).
- Rear shock is preload and rebound adjustable.
Double check throttle snap-back and brake pressure

Kill switch: Must be off to clear error codes
Modes: Park, Eco, Drive, Hyper, Reverse
Touchscreen toggle: Tap “S” to switch km/h to mph
Light controls:
- Position 1: Off
- Position 2: Running lights
- Position 3: Headlight + tail light (with brake light)
- Flash button also included

Before every ride:
- Check brakes, throttle return, and chain tension
Weekly/after off-road use:
- Clean chain, check spoke tension, inspect for loose bolts
First 50–100 miles:
- Expect initial stretching of chain and bedding-in of brakes
Brake Bedding Process:
- Accelerate → hard brake → repeat multiple times to seat pads
Cleaning Tips:
- Remove battery before washing
- Cover electronics and battery connector with plastic
- Avoid spraying directly at controls or screen