EBMX X9000 Controller Installation Guide

Pre-Installation Checklist

Turn your breaker off
Disconnect the battery and briefly power on the bike to discharge remaining current
Gather tools: Allen wrenches (2.5mm–5mm), scissors or Dykes, zip ties, electrical tape, Loctite, wobble-style ratchet (recommended)

* An additional EBMX wiring harness adapter may be required for specific bike models.

Unbolt Panels and Controller
- Remove side panel bolts, ignition bolts, and plastic tray (Allen 3mm–5mm)
- Remove top controller bolts
- Remove the plastic shield behind the controller (Phillips)
Disconnect Wiring
- Remove motor phase wires: blue, green, yellow
- Remove battery power wires: red (positive), black (ground)
- Unplug all connectors from the controller (CANbus plug will not be reused)
- Set ignition unit aside without unplugging
Remove Controller Unit
- Take note of phase wire routing (down to motor) and power wires (up to battery)
- Compare new and old controller for fitment reference

Prep Battery Wiring
- Remove OEM tape and carefully split red/black battery wires for routing
- Cut wire sleeve back just enough to allow flexibility (avoid damaging insulation)
Organize Hardware
- Sort bolts by size and match 5 large mounting bolts with lock washers
- Set aside additional spacers for controller frame mounting

Mount Motor Phase Wires
- Yellow → far left terminal
- Green → center
- Blue → right terminal
- Hand-tighten with Allen wrench (do not use power tools)
Mount Battery Power Wires
- Red → right terminal
- Black → left terminal
- Use supplied bolts and lock washers with Loctite
- Tighten snug, not over-torqued
Install Controller to Frame
- Use included spacers and bolts
- Apply Loctite to all threads
- Reinstall plastic tray and brackets
- Ensure wires are routed cleanly and not pinched

Install Sur Ron Harness
- If you have a different brand electric dirt bike (E-Ride Pro, Talaria, etc) confirm that you have your EBMX adapting harness, if one is needed.
- Install adapter to bike harness
- Connect harness (or adapter) to controller input port using alignment notches and arrows
- Optional: Wrap with electrical tape for weatherproofing
Secure Unused Plugs
- Tape off unused connectors and tuck away securely
2-to-1 Splitter Installation
- Connect to display and regen thumb throttle
- Route cables cleanly through frame
Install Bluetooth Dongle
- Plug into controller and secure away from metal for best reception
Cable Management
- Use zip ties to secure wiring to frame and brake lines
- Avoid over-tightening to allow minor wire movement

Install EBMX App
- Download from iOS App Store or Google Play (search “EBMX”)
Connect Controller
- Open the app and pair with your EBMX X9000 via Bluetooth
Basic Settings
- Vehicle: Sur Ron Light Bee (Our example)
- Motor: Stock (Change this if you've upgraded your motor)
- Battery: 16s Stock (Check your owner's manual for specs)
- Direction: Counter clockwise
- Units: Fahrenheit, MPH
Throttle Calibration
- Run twist and thumb throttle calibration through app
- Follow prompts for zero input and full input cycles
Hall Sensor Calibration
- Lift rear wheel before beginning
- From settings, select “Hall Sensor Calibration” and start
- Let it run and save when complete
Save Settings
- Be sure to save each time you finish a configuration section

Reinstall Battery
- Drop battery into tray and reconnect
- Turn on breaker and bike
Check Display
- Confirm display powers on and shows:
  - Speed (MPH)
  - Voltage
  - Power level
  - Motor and controller temperature
Test Handlebar Controls
- Ensure no contact between throttle, display, and brake levers
- Route and secure wires so they don't bind during steering movement
Mode Switching
- Press and hold the display’s lower button to switch between Street and Race modes
- Tap through Power Levels 1–3 within each mode

* May require battery upgrade to achieve these outputs.

EBMX X9000 Controller Installation GuideUpdated an hour ago